The L60 is an advanced phase comparison relay intended for application on overhead transmission lines, including series compensated lines, and high voltage underground cables of any voltage level. Both three pole and single pole tripping and reclosing schemes are available. As part of the Universal Relay (UR) Family, the L60 offers unparalleled digital protection and control.

What's New in the L60:

• Embedded Ethernet Switch Module - Reduces the overall cost of creating an Ethernet network by eliminating the need for external Ethernet Switches
• Enhanced Front Panel - New Vertical amp; Horizontal Front Panel provides:
  - Larger, bright display
  - User-Programmable Pushbutton option - 16 on horizontal, 6 on vertical
  - Easy labeling of LEDs and Pushbuttons
  - Ability to remove power supply without removing door
  - Easy upgrading of installed units - Full backwards compatibility
• Security Enhancements - Enabling NERC CIP compliance:
  - Remote and Local Setting and Control passwords
  - Configurable lockout responses to unsuccessful password access attempts
  - Successful password access logged in Event Record
• Double Point Breaker/Switch Status - Breaker and Isolator Switch status using two inputs to determine status and is available in DNP3.0 and IEC61850 protocols
• Tripping without Logic - Allows for direct tripping from protection elements without the need for configuring Flexlogic Equations

• Single and three pole tripping and reclosing, with a typical tripping time of 3/4 power cycle
• Cost effective and reliable solution in systems with communication links based on Power Line Carrier
• Advanced algorithms for channel noise immunity, accurate per-channel signal asymmetry and channel delay compensation
• Secure operation during external faults on breaker-and-a-half applications, with currents treated independently for maximum security
• FlexLogic™ programmable logic
• Virtual I/O (reduce hardware cost)
• Expandable I/O
• Flash memory for field upgrades
• Optional user programmable pushbuttons
• User programmable LEDs, fault reports, display messages, and self tests
• Drawout modules for serviceability
• Common modules (reduce spare cost)
• Test mode for I/Os
• IRIG-B time synchronization and repeater

• HV and EHV transmission lines
• Breaker-and-a-half and Ring-Bus configurations
• Up to four shots of single/three pole automatic breaker reclosing in multi-breaker schemes
• Backup protection for overhead AC Transmission lines

• Dual or single phase comparison with permissive and blocking schemes for 2 and 3 terminal applications
• Undervoltage, overvoltage, and multiple instantaneous, time, directional overcurrent
• 3 zone phase and ground distance protection
• Wattmetric zero-sequence directional function
• Single-pole, dual-breaker autorecloser and synchronism check
• CT failure, VT fuse failure
• Disturbance detector

• Breaker condition monitoring including breaker arcing current (I²t) and trip counter
• Metering - Current, voltage, power, energy and frequency
• Oscillography - 64 samples/cycle, up to 64 records
• Event Recorder - 1024 time tagged events, with 0.5ms scan of digital inputs
• Datalogger- Up to 16 channels with user selectable sampling rate
• Fault Locator

• 2 x 20 character front panel display and keypad for local access
• 48 programmable LED indicators
• User-programmable pushbuttons providing local control
• Multi-language support - French, Chinese, Russian options
• EnerVista™ UR Setup software for configuration, monitoring and troubleshooting

• Front Panel RS232 port
• Up to two RS485 ports (up to 115 kbps)
• Ethernet port: Redundant 10BaseFL or 100BaseFX fiber optics
• Embedded Ethernet Switch for direct networking of UR devices
• Inter-relay communications interfaces, RS422, G.703, IEEE C37.94
• Direct I/O - Exchange inputs and outputs between relays with reduced wiring
• Modbus RTU and TCP/IP
• IEC61850
• DNP 3.0 RTU and TCP/IP
• IEC60870-5-104
• Ethernet Global Data (EGD)